xtouch mini osculator to atem midi template

#Xtouch mini osculator to atem midi template full#
#Xtouch mini osculator to atem midi template software#
#Xtouch mini osculator to atem midi template download#
#Xtouch mini osculator to atem midi template mac#

If you connect multiple switchers to atemOSC, you will need to provide a nickname for each switcher and use that nickname in the address to specify which switcher to send the command to. By default, all commands without a nickname will be sent to the first switcher with no nickname. If you only want to connect to a single ATEM switcher, leave the nickname field blank and use the addresses below as normal. atemOSC will ignore all OSC commands it receives whose address does not start with /atem/. The list below is just an overview of what the addresses may look like for a generic switcher.Īll addresses must start with /atem/.

#Xtouch mini osculator to atem midi template full#

The full list of the OSC-addresses available for your switcher can be obtained by going to the “OSC Addresses” tab once you’ve connected atemOSC to your switcher. Usage with ProPresenter and OSCulator (MIDI) by Tiffany Howard: Usage with OSCulator (MIDI) by Morgan Warf: Usage with OSCulator (MIDI) by John Barker: Usage with Ableton Live and OSCulator (MIDI) by Jake Gosselin:

TouchOSC Layout (iPad) by Peter Steffey:.

Open Stage Control Layout by Peter Steffey:.

If you would like to control your switcher using a mobile device, you can use TouchOSC or Open Stage Control. If you would like to control AtemOSC directly using MIDI, comment on Issue #111 to let us know.

#Xtouch mini osculator to atem midi template software#

If you would like to control your switcher using a MIDI board or device, consider pairing this software with OSCulator or MidiPipe. SendOSC also enables using AtemOSC with ControllerMate and X-keys. See the actionscript example in this repository for an example of using AppleScript and sendOSC.

#Xtouch mini osculator to atem midi template download#

If you would like to send OSC from AppleScript or Terminal commands, you can download and use the sendosc command.

You can find the IP address of a macOS computer by going to System Preferences > Network or by running ifconfig in a terminal window. If you are sending atemOSC messages from another device, you will need to send it to the IP address of the computer running atemOSC on the port that atemOSC is listening on. If you are sending atemOSC messages from a queueing software or translation software on the same computer that atemOSC is running on, make sure to send messages to 127.0.0.1 (localhost) on the port that atemOSC is listening on. If you set an outgoing IP address and port, atemOSC will send status updates and feedback OSC messages to the IP address and port you specified.

Under Assets, select atemOSC_.dmgĪfter launching the application, enter the IP address of the switcher and which local port to listen on (default 3333), and then send OSC commands to the IP address of the computer running atemOSC that port.

For a version that supports older versions of the Atem SDK, scroll down until you find the release for the version you want.

#Xtouch mini osculator to atem midi template mac#

S: means short click and L: means long click.įLT ALT / LAND ALT rotary changes function from FLT ALT to LAND ALT with short click.AtemOSC is a network proxy, listening for commands following the OSC protocol and executing those commands on Blackmagic ATEM video switchers.įor best results, run the latest version of atemOSC, make sure your switcher(s) is running the latest version of the ATEM firmware, and make sure that the Mac that atemOSC is running on has the latest version of ATEM Software Control installed (or at least the same version as the switcher firmware, if the switcher does not support the latest version). Those means which layer that specific function is mapped. In overlay some functions are marked with (a) and (b).

Load aircraft to your favourite airport and select Template -> Apply template to this aircraft -> Select “pmdg_737_700_v1.0” from the list.

Import template by selecting Templates -> Import template -> select “pmdg_737_700_v1.0.tmpl”.

In AAO import scripts by selecting Scripting -> Import Scripts -> select “pmdg_737_700_scripts.xml”.

Printable overlay is included in the zip. Only Collins version is supported, Honeywell is not tested. BBJ and Freighter versions are not tested and possible not supported. Template is tested only with PMDG 737-700. AAO XTouch mini template for PMDG 737-700 for MSFS